Topic Location: ClientView Pane Reference
Use this pane to form a list of configuration instructions. Once pane is created there is a drop down menu in the Instruction Type field. The Instruction Type Field will allow the user to create several of these messages to form a list of instructions for Outseize control on CAS channels. Within ClientView you must create a separate Outseize Instruction entry for each instruction that you add to the list. Once list is created you can assign the Variant to a specific Channel Group. The IMG uses the list created to perform an Outseize on channels in a Channel Group.
Important Note: The order in which the instructions appear in the ClientView tree is the order in which they will be sent.
Dialogic IMG EMS -> Signaling -> <Variant Name> -> Outseize Instruction
19 per Signaling Variant
|
Outseize Instruction Type |
Instructs Switch To: |
|
Scan for Wink N |
Scan for Wink N using the appropriate wink parameters. Scan a specific Wink like Wink 3 etc. |
|
Report Call Processing Event |
Report the completion of the previous instruction along with any associated data. This instruction typically follows a Scan for Wink or Scan for Off-Hook instruction. |
|
Outpulse Stage N address info |
Outpulse a given stage of digits. You can first Outpulse stage: 1 string: 1 and then stage: 2 string; 2. |
|
Send Host Acknowledgement |
Send the host a positive ACK to an Outseize Control message if all previous instructions have been successfully carried out. If a previous instruction is not successful, the list aborts at that point and the host is sent a negative ACK. If this instruction is sent, include only one per message and it should be the last instruction before Wait For Host Control. |
|
Delay N Milliseconds |
Use this inseize instruction to enter a delay between two Inseize Instructions |
|
Outseize Instruction Type |
Second Field: (Wink #, Event, Stage Number) |
Data |
|
Scan for Wink |
Wink Number |
Wink 1 — Wink 8 |
|
Report Call Processing Event |
Event |
· Off Hook · Wink 1 — Wink 8 · DialTone Detected · Backward R2 · First Digit Detected |
|
Outpulse Stage N address info |
Stage Number |
· Stage 1 · Stage 2 · Stage 3 · Stage 4 |
|
Send Host Acknowledgement |
DATA |
NO DATA |
|
Delay N Milliseconds |
DATA |
NO DATA |
|
|
|
|
Applies to Instruction Type of 'Delay n Milliseconds'. Use this Inseize instruction to enter a delay between two Outseize Instructions. Use the slider or enter a value in the Value: box
|
Outseize Instruction Type |
Instructs Switch To: |
|
Scan for Wink N |
Scan for Wink N using the appropriate wink parameters. Scan a specific Wink like Wink 3 etc. |
|
Report Call Processing Event |
Report the completion of the previous instruction along with any associated data. This instruction typically follows a Scan for Wink or Scan for Off-Hook instruction. |
|
Outpulse Stage N address info |
Outpulse a given stage of digits. You can first Outpulse stage: 1 string: 1 and then stage: 2 string; 2. |
|
Send Host Acknowledgement |
Send the host a positive ACK to an Outseize Control message if all previous instructions have been successfully carried out. If a previous instruction is not successful, the list aborts at that point and the host is sent a negative ACK. If this instruction is sent, include only one per message and it should be the last instruction before Wait For Host Control. |
|
Cancel R2 Receiver |
Release a DSP MFR2 Tone Receiver. |
|
Scan for backward R2 signal |
Scan for an MFR2 backward signal. |
|
Outseize Instruction Type |
Second Field: (Wink #, Event, Stage Number) |
DATA |
|
Scan for Wink N |
Wink Number |
Wink 1 — Wink 8 |
|
Report Call Processing Event |
Event |
· Off Hook · Dial Tone Detected · Backward R2 · First Digit Detected |
|
Send Host Acknowledgement |
DATA |
NO DATA |
|
Cancel R2 Receiver |
DATA |
NO DATA |
|
Scan for backward R2 signal |
DATA |
NO DATA |
Not Used in E1