IP Resources Attributes

You can assign attributes to a VoIP module during initial configuration by using the Resource Attribute Configure message.

You can assign attributes during call set-up by using the Route Control or Outseize Control messages with Address Information Blocks (AIBs).

You can dynamically assign some attributes to a channel after call setup by using the Resource Attribute Configure message with the span/channel AIB.

If you change VoIP resource configuration with the Resource Attribute Configure message, the local copy of the configuration maintained by SIP and H.323 software remains unchanged. You must resynchronize the configurations as follows:

• Non-CSA users send the Resynchronize VoIP Media Parameters TLV (0x0284) in the VoIP Protocol Configure (0x00EE) message. Refer to the 0x0284 Resynchronize VoIP Media Parameter in the API Reference for the details of this TLV.

The following tables show the default values for IP Resource Attributes and indicate if you can configure them dynamically on an active connection.

Voice over Internet Protocol. The delivery of voice information in digital form in discrete packets rather than in the traditional circuit-committed protocols of the public-switched telephone network (PSTN).

Outgoing call setup during real-time call processing on a specific channel.

See Address Information Block.

Session-Initiation Protocol. A signaling protocol used for establishing sessions in an IP network. A session could be a simple, two-way telephone call, or it could be a collaborative multi-media conference session.

ITU-T standard defines a set of call control, channel setup, and codec specifications for transmitting real-time voice and video over networks that do not offer guaranteed service or quality of service.

See Converged Services Administrator.

Tag-Length-Value block. A standardized block that allows data to inserted in a standard way into API messages.

Internet Protocol. Part of the TCP/IP family of protocols used to route messages and tracks the addresses of nodes.

A device that translates calls between an IP network and another network, typically the PSTN.

The point in the Excel platform where a DS0 connects to a network. Also known as a "socket."

Real-Time Transport Control Protocol.

Real-Time Transport Protocol. Supports transport of real-time data like interactive voice and video over packet-switched networks.

TLV Tag and Name	Default Setting	Dynamic Configuration Supported
0x01D0 Gateway Mode	Non Port Consuming	No
0x01D4 Type of Service	See TLV Format	Yes
0x01DF UDP Source Port Validate	Enabled	Yes
0x01EC Media Inactivity Detection Timer	Disabled	No

TLV Tag and Name	Default Setting	Dynamic Configuration Supported
0x01C5 Fax Type Enable	Disabled	No
0x01C7 Fax Bypass Coder Type	Disabled	No
0x01D2 Fax Payload Redundancy	Disabled	No
0x01E1 Fax Compatibility Mode	Backward compatible mode	No
0x01E2 RFC 2833 Enable	Disabled	Yes
0x01E6 Source T.38 Port	No default	Yes
0x01E7 Destination T.38 Port	No default	Yes
0x01E8 Source RTCP Port	One offset from source RTP port	Yes
0x01E9 Destination RTCP Port	One offset from destination RTCP port	Yes

TLV Tag and Name	Default Setting	Dynamic Configuration Supported
0x0100 RTP Payload Type	G.711µ-Law	Yes
0x0101 RTP Payload Size	1X	Yes
0x0102 RTP Silence Suppression	Disabled	Yes
0x0103 RTP Echo Cancellation	Enabled	Yes
0x01C2 Minimum Jitter Buffer Delay	75 ms	No
0x01C3 Maximum Jitter Buffer Delay	150 ms	No
0x01C4 Adaptation Rate	7	No
0x01D1 RTP Payload Redundancy	Disabled	No
0x01DB Connection Mode	See the TLV format.	Yes
0x01E2 RFC 2833 Enable	Disabled	Yes
0x01E8 Source RTCP Port	One offset from destination RTP port	Yes
0x01E9 Destination RTCP Port	One offset from destination RTP port	Yes