Index words list

AL2
AL3
application
Understanding the host application model
Tasks for configuring the 3G-324M Interface
audio/video synchronization

Begin state
BeginCallSetup state
board configuration

call flows
   Example 1: Negotiating video with AL3
   Example 2: Negotiating video with AL2
   Example 3: Negotiating fast call setup using MONA
   Example 4: Using simplified application logic to set up calls
call monitoring
call setup
   Setup functions
   Example 4: Using simplified application logic to set up calls
call states
    Begin state
    BeginCallSetup state
    call state sequence
    Created state
    End state
    EndSession state
    MediaSetup state
CG board
channel
    closing and reopening
    configuration
    connecting
    creating
       Creating a channel
       MSP_CHANNEL_ADDR
    decoder
    defining for AMR transcoding
    defining jitter buffer parameters
    encoder
    pass-through
       h324PassthruDTMFMode
       Transferring DTMF digits according to RFC 2833
    setting MSPP channel parameters
commands
    creating and sending MSPP commands
    MSP_CMD_JITTER_CHG_VIDEO_LATENCY
    MSP_CMD_JITTER_NORMALIZE_VIDEO_LATENCY_BUF
    MSP_CMD_JITTER_PURGE_VIDEO_LATENCY_BUF
    MSP_CMD_RTPFDX_CONFIG
       MSPP queries and commands for the 3G-324M Interface
       Setting timestamp frequencies for full-duplex RTP endpoints
    MSP_CMD_RTPFDX_DISCARD_PENDING_FRAMES
       MSPP queries and commands for the 3G-324M Interface
       Discarding leading partial frame video packets
    MSP_CMD_RTPFDX_IFRAME_NOTIFY_CTRL
       MSPP queries and commands for the 3G-324M Interface
       Enabling I-frame notification
    MSP_CMD_RTPFDX_LINK_EVENTS
    MSP_CMD_RTPFDX_MAP
    MSP_CMD_RTPFDX_OUT_OF_BAND
    MSP_CMD_RTPFDX_RTCP_EVENTS
    MSP_CMD_RTPFDX_STOP_VIDEO_RX
       Ensuring a smooth transition when the video source changes
       MSPP queries and commands for the 3G-324M Interface
    MSP_CMD_RTPFDX_VIDEO_RTP_PKTSZ_CTRL
       MSPP queries and commands for the 3G-324M Interface
       Adjusting RTP packetization parameters
    MSP_CMD_RTPFDX_VIDEO_SKEW_TIME
    MSPP queries and commands for the 3G-324M Interface
configuration
   Configuring the board
   Designing the 3G-324M Interface channel configurations
Created state

decoder configuration information (DCI)
DEMUX
documentation
DTMF
   h324PassthruDTMFMode
   h324PassthruPlayRFC2833
   Modifying the RFC 2833 DTMF configuration
   Transferring DTMF digits according to RFC 2833

End state
endpoint
    connecting
    creating
       Creating the MUX endpoint
       Creating an endpoint
    defining RTP addresses and port numbers
    H.263
       MSPP queries and commands for the 3G-324M Interface
       Video channel types
       IPv4 video endpoint types
       IPv6 video endpoint types
    H.263+
    H.264
       Video channel types
       IPv4 video endpoint types
       IPv6 video endpoint types
       MSPP queries and commands for the 3G-324M Interface
    IPv4
       IPv4 audio endpoint types
       IPv4 video endpoint types
    IPv6
       IPv6 video endpoint types
       IPv4 video endpoint types
    MPEG-4
       MSPP queries and commands for the 3G-324M Interface
       IPv6 video endpoint types
       IPv4 audio endpoint types
    MUX
       MSP_ENDPOINT_PARAMETER
       MUX_ENDPOINT_ADDR
       MUX endpoint type
    setting configuration parameters for
    setting RTP configuration parameters
       RTPRTCP_ENDPOINT_PARMS
       RTPRTCP_V6_ENDPOINT_ADDR
       RTPRTCP_V6_ENDPOINT_PARMS
EndSession state
error handling
errors
   Numerical error summary
   Alphabetical error summary
   Working with H.324M error codes
events
    formatting
    numerical summary
    submitting
    working with