The following table lists the framer driver errors (0x0D40, 0x0D50):
|
Error name |
Hex |
Description |
Category |
|---|---|---|---|
|
FRMR_ERR_NO_HW_ADDRESS |
0x0D41 |
Could not find the framer hardware. |
2 |
|
FRMR_ERR_SIGX_NO_READY |
0x0D42 |
Failed to write SIGx. The board may have timed out. |
2 |
|
FRMR_ERR_PCC_NO_READY |
0x0D43 |
Failed to write per-channel control. The board may have timed out. |
2 |
|
FRMR_ERR_UNRECOG_LINE_MODE |
0x0D44 |
Invalid entry specified with the NetworkInterface.T1E1[x].Type keyword (PRI, RAW or CAS). |
4 |
|
FRMR_ERR_UNRECOG_LINE_TYPE |
0x0D45 |
Invalid entry specified with the NetworkInterface.T1E1[x].FrameType keyword (CEPT, D4, or ESF). |
4 |
|
FRMR_ERR_UNRECOG_LINE_CODE |
0x0D46 |
Invalid entry specified with the NetworkInterface.T1E1[x].LineCode keyword (B8ZS, HDB3, or AMI). |
4 |
|
FRMR_ERR_NO_WRITE_EQ |
0x0D47 |
Unable to read back the equalizer data after writing. |
2 |
|
FRMR_ERR_NO_WRITE_PULSESHAPE |
0x0D48 |
Unable to read back the pulse shape after writing. |
2 |
|
FRMR_ERR_NO_IND_PULSESHAPE |
0x0D49 |
Error reading and writing indirect registers at boot time. |
2 |
|
FRMR_ERR_DATA_LINES_TST_FAIL |
0x0D4A |
Error reading and writing walking ones at boot time. |
2 |
|
FRMR_ERR_ADD_LINES_TST_FAIL |
0x0D4B |
Error reading and writing walking ones at boot time. |
2 |
|
FRMR_ERR_NO_IND_EQUALIZER |
0x0D4C |
Error reading and writing indirect registers at boot time. |
2 |
|
FRMR_ERR_NO_IND_SIGX |
0x0D4D |
Error reading and writing indirect registers at boot time. |
2 |
|
FRMR_ERR_NO_IND_TPSC |
0x0D4E |
Error reading and writing indirect registers at boot time. |
2 |
|
FRMR_ERR_NO_IND_RPSC |
0x0D4F |
Error reading and writing indirect registers at boot time. |
2 |
|
FRMR_ERR_UNABLE_TO_CREATE TIMER |
0x0D50 |
Idle thread. Unable to create a timer instance. |
3 |
|
FRMR_ERR_NO_MORE_MON_AVAILABLE |
0x0D51 |
No address available to add to the PMON list. |
3 |
|
FRMR_ERR_PMON_ADDR_NOT_FOUND |
0x0D52 |
Address to be removed from PMON not found. |
3 |
|
FRMR_ERR_OUT_OF_MEMORY |
0x0D53 |
Failed to create a message buffer for PMON. |
3 |
|
FRMR_ERR_OOMEMORY_SEND_PARMS |
0x0D54 |
Parameter file return data to host is failing. |
3 |
|
FRMR_ERR_OOMEMORY_SEND_BUFF |
0x0D55 |
Parameter file return data to host (buffer) is failing. |
3 |
|
FRMR_ERR_WRONG_BUFFER_SIZE |
0x0D56 |
Data file expected by the command was the wrong size. |
3 |
|
FRMR_UNABLE_TO_ALLOCATE_MEMORY |
0x0D57 |
Failed to allocate a memory block. |
3 |
|
FRMR_ERR_DISABLING_IRQS |
0x0D58 |
Too many IRQs pending. Resolution: Disable all IRQs. |
5 |
|
FRMR_ERR_NO_MONITORS_AVAILABLE |
0x0D59 |
No available trunk monitor channels. |
3 |
|
FRMR_ERR_NO_VIRTUAL_FUNCTION |
0x0D5A |
No virtual function overriding base class function. |
3 |
|
FRMR_ERR_IRQ_BUFFER_FULL |
0x0D5B |
Ring buffer for IRQ data was full when trying to add data. |
3 |
|
FRMR_ERR_CANNOT_CREATE_IRQ_BUF |
0x0D5C |
Failed to create a ring buffer. |
3 |
|
FRMR_ERR_NOT_INITIALIZED |
0x0D5D |
Default error results are set to this error. Error code not set correctly. |
3 |
|
FRMR_ERR_NO_BUFFER_LEFT |
0x0D5E |
No buffers available to send up the driver variables. |
3 |
|
FRMR_ERR_UNRECOG_RET_MSG_TYPE |
0x0D5F |
Sending status found an unrecognized message type to send. |
3 |
|
FRMR_ERR_NO_HANDLE_FOR_HMIC |
0x0D60 |
Unable to get handle to HMIC. |
3 |
|
FRMR_ERR_FUNC_NOT_SUPPORTED |
0x0D61 |
Requested operation is not supported. |
1 |