Guidance required on Configuration SS7MD board

Hi,

  We have a ss7MD with two E1 Links towards a Single OPC and Single LocalPC. The configuration was working fine for Single E1.So to increase the call capacity we have connected Two E1 to the single Board.

SLC for first E1 is 0 and SLC for II E1 is 1.

I tried the attached configuration - calls are successful. , But when I pulled off the first line, calls are not successful.

So can you please check are there are any issues with the configuration.

********************************************************************************
*
* Example Protocol Configuration File (example_config.txt) for use with
* the DSI Development Package.
*
* Boards supported are SPCI, SS7MD, SS7HD and the SS7LD range.
* Note - Not all boards are supported on all operating system.
*
* This file needs to be modified to suit individual circumstances.
* Refer to the relevant Programmer's Manuals for further details.
*
********************************************************************************
*
*
* Configure individual boards:
* SS7_BOARD <board_id> <board_type> <flags> <code_file> <run_mode>
*
* For SPCI2S boards:
*SS7_BOARD 0 SPCI2S 0x0043 ./DC/ss7.dc3 MTP2
*
* For SPCI4 boards:
*SS7_BOARD 0 SPCI4 0x0043 ./DC/ss7.dc3 MTP2
*
* For SS7HD PCI boards:
*SS7_BOARD 0 SS7HDP 0x0043 ./DC/ss7.dc4 MTP2
*
* For SS7HD cP boards:
*SS7_BOARD 0 SS7HDC 0x0043 ./DC/ss7.dc4 MTP2
*
* For SS7HD PCIe boards:
*SS7_BOARD 0 SS7HDE 0x0043 ./DC/ss7.dc4 MTP2
*
* For SS7MD boards:
SS7_BOARD 0 SS7MD 0x0001 ./DC/ss7.dc6 LSL
*
* For SS7LD boards:
*SS7_BOARD 0 SS7LD 0x0001 ./DC/ss7.dc7 MTP2
*
TRACE_MOD_ID 0xef * Set default trace module to 0xef.
*
* Configure individual T1/E1 interfaces:
* LIU_CONFIG <board_id> <liu_id> <liu_type> <line_code> <frame_format>
* <crc_mode> [<build_out>]
LIU_CONFIG 0 0 5 1 1 1
LIU_CONFIG 0 1 5 1 1 1
*
* ATM parameters:
*
* Configure ATM module (SS7MD boards only):
* ATM_CONFIG <options> <num_streams>
*
* ATM_CONFIG 0x0000 4
*
* Define an ATM Cell Stream (SS7MD boards only):
* ATM_STREAM <id> <board_id> <cellstream_id> <liu_id> <options> <ima_frame_len> <max_frame_len>
* <def_vpi> <def_vci> <timeslot>
*
* ATM_STREAM 3 0 1 0 0x01 0 280 12 10 0xfffefffe
*
*
* Configure MTP3 module:
* MTP parameters:
*
* MTP_CONFIG <reserved> <reserved> <options>
MTP_CONFIG 0 0 0x00040000
*
* Define linksets:
* MTP_LINKSET <linkset_id> <adjacent_spc> <num_links> <flags> <local_spc> <ssf>
MTP_LINKSET 0 1281 2 0x0000 1252 0x0c

*MTP_LINKSET 1 1281 1 0x0000 1252 0x0c
*
* Define signaling links:
* MTP_LINK <link_id> <linkset_id> <link_ref> <slc> <board_id> <blink>
* <stream> <timeslot> <flags>
*
* For SPCI4 / SPCI2S, SS7MD and SS7LD boards:
MTP_LINK 0 0 0 0 0 0 0 16 0x0006
MTP_LINK 1 0 1 1 0 1 1 16 0x0006
* For SS7HD boards:
*MTP_LINK 0 0 0 0 0 0-0 0 16 0x0006
*MTP_LINK 1 0 1 1 1 0-1 0 1 0x0006
*
* Define QSAAL links (SS7MD boards only):
* MTP_LINK <link_id> <linkset_id> <link_ref> <slc> <board_id> <blink>
* <atm_stream> <vpi-vci> <flags> ATM
*
* MTP_LINK 0 0 0 0 0 0 0 5-10 0x0006 ATM
*
* Define a route for each remote signaling point:
* MTP_ROUTE <dpc> <linkset_id> <user_part_mask>
MTP_ROUTE 1281 0 0x0020
*
* Define any user provided Layer 4 protocol:
* MTP_USER_PART [NC] <service_ind> <module_id>
* MTP_USER_PART NC0 0x0a 0x2d
*
*
* ISUP parameters:
*
* Configure ISUP module:
* ISUP_CONFIG <reserved> <reserved> <user_id> <options> <num_grps> <num_ccts>
ISUP_CONFIG 0 0 0x1d 0x0435 8 64
*
* Configure ISUP circuit groups:
* ISUP_CFG_CCTGRP <gid> <dpc> <base_cic> <base_cid> <cic_mask> <options>
* <user_inst> <user_id> <opc> <ssf> <variant> <options2>
*ISUP_CFG_CCTGRP 0 1281 0x01 0x01 0x7fff7fff 0x001c 0 0x1d 1252 0x8 0 0x00
*ISUP_CFG_CCTGRP 0 1181 0x01 0x01 0x7fff7fff 0x00000003 0 0x1d 1151 0x0c 1 0x00

ISUP_CFG_CCTGRP 0 1281 0x01 0x01 0x7fff7fff 0x00000003 0 0x1d 1252 0x0c 1 0x00
ISUP_CFG_CCTGRP 1 1281 0x21 0x21 0x7fff7fff 0x00000003 0 0x1d 1252 0x0c 1 0x00
*
*
* TUP parameters:
* Configure TUP module:
* TUP_CONFIG <reserved> <reserved> <user_id> <options> <num_grps> <num_ccts>
*TUP_CONFIG 0 0 0x1d 0x8141 4 64
*
* Define TUP circuit groups:
* TUP_CFG_CCTGRP <gid> <dpc> <base_cic> <base_cid> <cic_mask> <options>
* <user_inst> <user_id> <opc> <ssf>
*TUP_CFG_CCTGRP 0 1 0x01 0x01 0x7fff7fff 0x0030 0 0x1d 2 0x08
*
*
* SCCP parameters:
*
* Configure SCCP module:
* SCCP_CONFIG <local_spc> <ssf> <options> [<send_uis>]
* SCCP_CONFIG 123 8 0
*
* Configure SCCP Sub-System Resource
* SCCP_SSR <ssr_id> RSP <remote_spc> <flags> <pc_mask>
* SCCP_SSR 1 RSP 1236 0
*
* SCCP_SSR <ssr_id> LSS <local_ssn> <module_id> <flags> <protocol>
* SCCP_SSR 2 LSS 0x07 0x0d 1 TCAP
*
* SCCP_SSR <ssr_id> RSS <remote_spc> <remote_ssn> <flags>
* SCCP_SSR 3 RSS 1236 0x67 0
*
* SCCP Concerned Sub-System Resource
* SCCP_CONC_SSR <id> <cssr_id> <ssr_id>
* SCCP_CONC_SSR 1 2 3
*
* Configure SCCP Trace
* SCCP_TRACE <op_evt_mask> <ip_evt_mask> <non_prim_mask>
* SCCP_TRACE 0x1 0x1 0x1
*
* Define Global Title Pattern
* SCCP_GTT_PATTERN <pattern_id> <addr_indicator> <pc> <ssn> <global_title> [<gtai_pattern>]
* SCCP_GTT_PATTERN 5 0x10 0x0000 0 0x001104 44/+
*
* Define Global Title Address
* SCCP_GTT_ADDRESS <address_id> <addr_indicator> <pc> <ssn> <global_title> [<gtai_replacement>]
* SCCP_GTT_ADDRESS 9 0x11 0x1234 0 0x001104 0-/-
*
* Add Entry in GTT Table
* SCCP_GTT <pattern_id> <mask> <primary_address_id> [<backup_address_id>]
* SCCP_GTT 5 R-/K 9
*
*
* TCAP parameters:
*
* Configure TCAP
* TCAP_CONFIG <base_ogdlg_id> <nog_dialogues> <base_icdlg_id> <nic_dialogues> <options> <dlg_hunt>
* [<addr_format>]
* TCAP_CONFIG 0x0000 8192 0x8000 8192 0x0000 0
*
* Define TCAP circuit groups:
* TCAP_CFG_DGRP <gid> <base_ogdlg_id> <nog_dialogues> <base_icdlg_id> <nic_dialogues> <options>
* <reserved>
* TCAP_CFG_DGRP 0 0x0000 1024 0x8000 1024 0 0
*
* Configure TCAP Trace
* TCAP_TRACE <op_evt_mask> <ip_evt_mask> <non_prim_mask>
* TCAP_TRACE 0x7 0xf 0x0
*
*
* MAP parameters:
*
* Configure MAP
* MAP_CONFIG <options>
* MAP_CONFIG 2
*
* Configure MAP Trace
* MAP_TRACE <op_evt_mask> <ip_evt_mask> <non_prim_mask>
* MAP_TRACE 0xf 0xf 0x4
*
*
* INAP parameters:
*
* Configure INAP
* INAP_CONFIG <options>
* INAP_CONFIG 2
*
* Configure INAP Functional Entities
* INAP_FE <fe_ref> <options> <sccp_address>
* INAP_FE 0x00000007 0x0000000f 0x00000000
*
* Configure INAP Application Context
* INAP_AC <ac_ref> <ac>
* INAP_AC 0x00 0xa109060704000101010000
*
* Configure INAP Trace
* INAP_TRACE <op_evt_mask> <ip_evt_mask> <non_prim_mask>
* INAP_TRACE 0xf 0xf 0x7f
*
*
* IS41 parameters:
*
* Configure IS41 TRACE
* IS41_TRACE <op_evt_mask> <ip_evt_mask> <non_prim_mask>
* IS41_TRACE 0xf 0xf 0xff
*
********************************************************************************
MTP_TRACE 0x20 2 0

ISUP_TRACE 1 1 4