|
Field name |
Type |
Default |
Units |
Description |
|---|---|---|---|---|
|
breaktime |
DWORD |
60 |
ms |
Break (on-hook) duration for dial pulses. Valid AG board and CG board range is 0 through 30000. |
|
dialtonewait |
DWORD |
5000 |
ms |
Maximum time to wait for dial tone (; character). Valid range is 0 through 65535. |
|
dtmfampl1 |
INT32 |
-6 |
dBm |
Amplitude of the low frequency component of the DTMF pair. Valid AG board and CG board range is -54 through -3. |
|
dtmfampl2 |
INT32 |
-4 |
dBm |
Amplitude of the high frequency component of the DTMF pair. Valid AG board and CG board range is -54 through -3. |
|
dtmfofftime |
DWORD |
80 |
ms |
Duration of the silence time between each digit. Valid AG board and CG board range is 0 through 65534. |
|
dtmfontime |
DWORD |
80 |
ms |
Duration of each DTMF or MF digit. Valid AG board and CG board range is 0 through 65534. |
|
flashtime |
DWORD |
500 |
ms |
Amount of time to assert the on-hook signaling pattern for a flash (! character). Valid AG board and CG board range is 0 through 65535. |
|
interpulse |
DWORD |
700 |
ms |
Inter-digit time for pulsed dialing. Valid AG board and CG board range is 0 through 30000. |
|
longpause |
DWORD |
5000 |
ms |
Amount of delay associated with the . (period) character. Valid range is 0 through 65535. |
|
maketime |
DWORD |
40 |
ms |
Make (off-hook) duration for dial pulses. Valid AG board and CG board range is 0 through 30000. |
|
method |
DWORD |
0 |
mask |
Type of signaling.
|
|
reserved |
DWORD |
0 |
internal |
Do not modify. |
|
shortpause |
DWORD |
2000 |
ms |
Amount of delay associated with the , (comma) character. Valid range is 0 through 65535. |
|
tonebandw1 |
DWORD |
40 |
Hz |
Bandwidth of the first frequency of the dial tone detector. Valid AG board and CG board range is 20 through 800. |
|
tonebandw2 |
DWORD |
40 |
Hz |
Bandwidth of the second frequency of the dial tone detector. Valid AG board and CG board range is 20 through 800. |
|
tonefreq1 |
DWORD |
350 |
Hz |
First (or only) dial tone frequency. Valid AG board and CG board range is 330 through 3600. |
|
tonefreq2 |
DWORD |
440 |
Hz |
Second dial tone frequency. Set this value to 0 (zero) to detect a single frequency. Valid AG board and CG board range is 330 through 3600. |
|
tonequalampl |
INT32 |
-28 |
dBm |
Minimum signal amplitude to qualify for dial tone detection. Valid AG board and CG board range is -40 through 0. |
|
tonequaltime |
DWORD |
50 |
ms |
Minimum duration of a qualified tone to be considered dial tone. Valid range is 0 through 32767. |
|
tonereflevel |
DWORD |
0xB000 |
IDU |
Do not modify. |
|
tonetotaltime |
DWORD |
0 |
ms |
Detects interrupted dial tones (stuttered dial tone) in certain countries. Defaults to 0 (zero), which indicates that dialing can proceed as soon as a dial tone is detected without waiting for stuttered dial tone to end. If set to a non-zero value, the value represents the total qualification time for dial tone, and the following occurs:
|